Exp-computer CD Traveler Plus Instrukcja Użytkownika

Portable CD-ROMUser’ Manual For CD Traveler - PCMCIA CD Traveler Plus - PCMCIA and Parallel

- -10CONNECTING THE AC ADAPTER1. Remove the PCMCIA interface card or Parallel Port connector from yourcomputer.2. Connect the AC adapter plug to

- -11POWER SWITCHStand-alone CD playerPressing the POWER button (as shown in „ of Figure 2) will switch the CDdrive power ‘on’ or ‘off’. The driv

- -12• Always remove old, weak or worn-out batteries promptly and dispose ofthem properly.• If you do not use this unit for a long period of time

- -13INSTALLATIONThe installation procedures have two sections for each type of interface.1. PCMCIA(PC Card) interface2. Parallel Port interface

- -14SOFTWARE INSTALLATIONSOFTWARE INSTALLATION FOR WINDOWS 95/98The “New Hardware Found” dialog box* will appear when you insert the CDCD Travel

- -15For user with a newer revision of Windows 95 or Windows 98, “UpdateDevice Driver Wizard” box * will appear. Click on “Next” button, let Win

- -16SOFTWARE INSTALLATION FOR WINDOWS NT 4.0PC CARD InterfaceCurrently there is no Plug and Play support for PC Card (PCMCIA) on theWindows NT 4

- -17Disk” button.Install from disk dialog box will prompt for device driver diskette.Either using “Browse” button or type in the path A:\winnt t

- -18INSTALLATION FOR PARALLEL PORT INTERFACEHARDWARE INSTALLATIONBefore you begin, make sure you turn OFF all power to your system beforeconnect

- -19Select "No" and click "Next>".2. Open "SCSI controllers". Click "Have Disk...". 3. Insert

- -2TABLE OF CONTENTPART NAME AND FUNCTIONTOP PANEL OF THE CD-ROM DRIVE 4REAR PANEL OF THE CD-ROM DRIVE 5BOTTOM OF THE CD-ROM DRIVE 6PARALLEL POR

- -207. Restart system, when prompted.VERIFY YOUR INSTALLATIONFrom “desk top” click on “my computer” icon. There should be addition CD-ROM drive’

- -21SOFTWARE INSTALLATION FOR WINDOWS NT 4.0In Windows NT 4.0, you may select “Control Panel” under “Settings” from the“Start” menu to open the

- -22Click OK to select the driver.Follow the on-screen instruction to continue. After finishing, Windows NT willprompt you to restart your compu

- -23BASIC OPERATING PROCEDURESFollow the instructions listed below to open the disc cover and insert/removea CD.Press the OPEN button. The disc

- -24INSTALLING THE APPLICATION SOFTWAREWindows 95/98 and Windows NT 4.0From “Start” go to “Setting”, “ Control Panel” then “Add/Remove Program”C

- -25It is not necessary to remove the PCMCIA interface card from the CD-ROMdrive when the CD-ROM is in stand-alone mode. You may store the card

- -26Headphone Jack• Connect your headphone to his jack for listening to audio CD. Line-Out Jack• Connect this jack to the LINE-IN jack of the so

- -27If your computer is equipped with a sound card, you can also connect theLINE-OUT jack of your CD-ROM to the LINE-IN jack of the sound card w

- -28TROUBLE SHOOTINGPCMCIA INTERFACESymptom: No “New Hardware Found” dialog box display.Solution: 1. The EXP card is NOT fully inserted.

- -29If you see the screen below, it means the PCMCIA device driveris not using 32-Bit Card Support. Follow on screen instructions byexcept all t

- -3PLAY AN AUDIO CD BY USING SOFTWARE 26TROUBLE SHOOTINGPCMCIA INTERFACE 28PARALLEL PORT INTERFACE 32REMOVING OR RE-INSTALLING THE DRIVERPCMCIA

- -30The EXP entry mayhave a yellow circlewith an exclamationpoint.This is an indicationthat the EXP CD didnot working properly.Double click on E

- -312. Device Manager shows resource for the EXP CD is available andthere is no conflicting device.In some computer, the I/O Range XXX, Interrup

- -32PARALLEL PORT INTERFACESymptom: No additional drive icon in “My Computer”. The EXP CD driverinstalled without any incident.Solution:1. Chec

- -33different setting can effect performance of the EXP CD. In somecases, the standard setting will even shut off signals the EXPCD needs, while

- -34REMOVING OR RE-INSTALLING THE DRIVERPCMCIA INTERFACEIf you need to remove or reinstalling the driver, make sure the EXP CD-ROM disk card is

- -35or “Update Device Driver Wizard” will be displayed.Follow the instruction on “Installation for PCMCIA Interface” section.PARALLEL PORT INTER

- -36INSTALL A CD TITLEDOS/Windows 3.xMost of the CD-ROM titles for Windows 3.1/3.11 contain the SETUP.EXE orINSTALL.EXE program in the CD disc.

- -37Windows 95The hot swapping is allowed with more limitation. To avoid system failure,always follow the below steps to hot remove the PCMCIA C

- -38APPENDIX ADEVICE DRIVER INSTALLATION FOR DOSPCMCIA InterfaceAutomatic InstallationThe INSTALL program helps you install the device driver in

- -39Manual InstallationYou may also manually install the Portable CD-ROM device driver if thedefault setting conflicts with your system. Please

- -4PRECAUTIONSRead this section carefully before starting to use thePortable CD-ROM Plus.CD-ROM DRIVE• Do not place heavy objects on the CD-ROM

- -40The example above shows the default setting. The /D: switch indicatesthe device name. It MUST be the same name as you specified by the /D:

- -41remove the installation diskette and press Y and ENTER to re-boot thePC.Most CD-ROM programs require a minimum of a 286 processor with MS-DO

- -42use the CD-ROM device. For notebook computer users, removing the cardwill preserve power and prolong battery life.Note: You are allowed to r

- -43EXP COMPUTER, INC. EXP MEMORY PRODUCTS.NON-TRANSFERABLE LIMITED WARRANTYEXP COMPUTER INC., AND EXP MEMORY PRODUCTS ("EXP") warrant

- -5CD-ROM PART NAMES AND FUNCTIONSTOP PANEL OF THE CD-ROM DRIVE:•• Open button:Press this button to open the disc cover.‚‚ On/Busy led:• This in

- -6• When the drive is in ‘play’ state, pressing the right edge of the buttonwill skip to the next track.• When the drive is in ‘play’ state, pr

- -7BOTTOM OF THE CD-ROM DRIVE:•• PCMCIA Interface Card Holder:Store the PCMCIA interface card when not used.‚‚ Battery Lid:Slide and lift up t

- -8PARALLEL PORT ADAPTER CABLE:•• Parallel port connector:Connect this connector to a computer (25 pin) parallel port (Printer port).‚‚ CD-ROM

- -9POWER SOURCE SWITCH is set to “PC” (Figure 4.a)The PCMCIA power direct is selected. Thus, the CD-ROMwill obtain power from PCMCIA socket of y