Exp-computer CD-820_CDG-820 Instrukcja Użytkownika

CD TRAVELERUSER’S MANUALW/ CD-ROM+ CARD

CONNECTING THE AC ADAPTERRemove the PCMCIA interface card from your computer.2. 3. Attach the AC adapter to the AC outlet.CAUTIONUse only the AC adapt

POWER SWITCHStand-alone CD playerPressing the POWER button (as shown in „ of Figure 2) will switch the CD drivepower ‘on’ or ‘off’. The drive also has

NOTICE• Use only the AC adapter provided with this unit or refer to the rear panel of thedrive for the correct AC adapter specification.• If you are n

HARDWARE INSTALLATIONBefore you begin, make sure you turn OFF all power to your system beforeconnecting the PCMCIA CD-ROM to your computer.1. Turn ove

SOFTWARE INSTALLATION FOR DOS/WINDOWS 3.1AUTOMATIC INSTALLATIONThis INSTALL program helps you install the device driver into your computereasily. Ple

NOTE:1. INSTALL.EXE is only for DOS/Windows 3.x Mode, DO NOT use it underWindows 95, unless you want to use this device under pure MS-DOS. Pleasesee A

MANUAL INSTALLATIONYou may manually install the device driver if the default setting conflicts with yoursystem. Try the following procedure to complet

SOFTWARE INSTALLATION FOR WINDOWS 95The following dialog box will appear when you are using the CD-ROM+ cardunder Windows 95 for the very first time.I

When the next dialog box appears, select “Portable CD-ROM” or “Portable CD-ROM + Game “ and click on the OK bottom.Follow the on-screen instruction to

B.) If previously installed as “CD-ROM + GAME”:With the CD-ROM drive connected, go to the Control Panel. Click on “System”.Then choose “Device Manager

EXP COMPUTER, INC. EXP MEMORY PRODUCTS.NON-TRANSFERABLE LIMITED WARRANTYEXP COMPUTER INC., AND EXP MEMORY PRODUCTS("EXP") warrants that the

BASIC OPERATING PROCEDURESFollow the instructions listed below to open the disc cover and insert/remove a CD.1. Press the OPEN button. The disc cover

USING THE PCMCIA CD-ROM AS A STAND-ALONE CD PLAYERIn a stand-alone audio CD player operation, the CD need either the AC adapter orbatteries for its po

 Headphone Jack• Connect your headphone to his jack for listening to audio CD.  Line-Out Jack• Connect this jack to the LINE-IN jack of the sound

2) Choose the Drivers icon from Control Panel, and choose the Add button to setup the driver [MCI] CD Audio.3) Start the Media Player.4) Select Device

INSTALL A CD TITLEDOS/Windows 3.xMost of the CD-ROM titles for Windows 3.1/3.11 contain the SETUP.EXE orINSTALL.EXE program in the CD disc. You need

Windows 95The hot-swapping is allowed with more limitation. To avoid system failure, alwaysfollow the below steps to hot remove the PCMCIA CD-ROM in W

APPENDIX AINSTALLING THE CD-ROM WITH THE GAME PORT ADAPTER(FOR CDG-820 MODEL ONLY)•• CD-ROM Connector:This connector connects to the CD-ROM drive.‚‚ G

Incompatible ListThe following notebooks have been tested and has been confirmedas incompatible with the Game Port connected to the CD-ROM kit:Dell La

APPENDIX BThe following procedures will allow you to use the device in a pure MS-DOSenvironment for those applications that will not run in Windows 95

• Click on "Finish" • Click on the right mousebutton on the new MS-DOSPrompt icon• Go to "Properties"• Go to "Program&quo

FCC COMPLIANCE STATEMENTSThis equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FC

• Click on the "Advanced"• Click the "MS-DOSmode" Click on "Specifya new MS-DOSconfiguration"• Click on "OK".

• The Next steps are to configure the DOS mode session for theDOS drivers that are needed to run the CD-ROM/Game card.• If you have a config.dos and a

APPENDIX CENABLING 32-BIT CARD SUPPORT OF WINDOWS 95Your system should be ready for PCMCIA socket support prior to operating the CD-ROM and Game Port.

In this case, double click on the PCMCIA Controller, and a dialog box will bedisplayed as below. Please place a check mark next to the current configu

APPENDIX DPCMCIA SOFTWARE(DOS/WINDOWS3.X) INFORMATIONIf you have installed the PCMCIA software, such as SystemSoft’s CardSoft orDatabook’s Cardtalk, t

The device driver names of the major PCMCIA software are listed below:Software/DeviceDriverSystemSoftCardSoftPhoenix AwardCardwareIBMThinkPadSocket Se

SYSTEMSOFT PCMCIA SOFTWARE SAMPLE CONFIG.SYS FILELASTDRIVE=ZDEVICE=C:\DOS\HIMEM.SYSDEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-D3FFFILES=40BUFFERS=20STACKS=

STACKS=9,256DEVICE=C:\CARDWARE\SSPCIC.EXEDEVICE=C:\CARDWARE\PCCS.EXEDEVICE=C:\CARDWARE\PCRM.EXE/AUTODETECTDEVICE=C:\CARDWARE\PCENABLE.EXEREM CDROM+GAM

CONTENTSPRECAUTIONS ... 2CD-ROM DRIVE ...

precautionsRead this section carefully before starting to use theportable PCMCIA CD-ROM.CD-ROM DRIVE• Do not place heavy objects on the CD-ROM drive.•

CD-ROM PART NAMES AND FUNCTIONSTOP PANEL OF THE CD-ROM DRIVE:•• Open button:Press this button to open the disc cover.‚‚ On/Busy led:• This indicator w

…… Next/Previous button: (for CD audio operation only)• When the drive is in play state, pressing the right edge of the button will skipto the next t

BOTTOM OF THE CD-ROM DRIVE:•• PCMCIA Interface Card Holder:Store the PCMCIA interface card when not used.‚‚ Battery Lid:Slide and lift up the lid to

CD-ROM POWERThere are three power source options to choose to power the CD Traveler:1. PCMCIA socket power direct2. AC adapter3. Battery.However, you