Exp-computer CD-420_CD-421_CD-621_CD-821 Instrukcja Użytkownika

PCMCIAPortable CD-ROMInstallation ManualCD-421

- -5INSTALLING THE BATTERIESThe CD-421 requires eight AA size batteries (not included) for operation.When using alkaline batteries, the battery l

- -6Figure 4REMOVING THE BATTERIES1. Remove the battery lid by sliding the cover in the direction of thearrow as shown in Figure 3.2. Lift up the

- -7HARDWARE INSTALLATIONMake sure you turn OFF all power to your system before connecting theCD-421 to your computer.1. Connect the PCMCIA inter

- -8SOFTWARE INSTALLATION FOR DOS/WINDOWS 3.1AUTOMATIC INSTALLATIONThe INSTALL program helps you install the device driver into thecomputer easil

- -9MANUAL INSTALLATIONYou may also manually install the CD-421 device driver if the defaultsetting conflicts with your system. Perform the follo

- -104. Add the following line at the TOP of your AUTOEXEC.BAT:drive:\path\MSCDEX.EXE /D:MSCD001 /M:4where drive:\path specifies the DOS directo

- -11SOFTWARE INSTALLATION FOR WINDOWS 95If your computer does not have Windows 95 installed yet, please refer tothe section titled “Using CD-421

- -12When the following dialog box appear, select CD-421 (I) card and clickon the OK bottom.Figure 8Follow the on-screen instruction to continue.

- -136. After the installation is completed, please refer to the next sectiontitled “Enabling 32-BIT CARD SUPPORT”.ENABLING 32-BIT CARD SUPPORT

- -14In this case, double click on the PCMCIA Controller, and a dialog boxwill be displayed as below. Please place a check mark next to thecurren

EXP COMPUTER, INC. EXP MEMORY PRODUCTS.NON-TRANSFERABLE LIMITED WARRANTYEXP COMPUTER INC., AND EXP MEMORY PRODUCTS("EXP")warrants that the Q

- -15SOFTWARE INSTALLATION FOR OS/2 WARPBefore installing CD-421 device driver for OS/2 WARP, make sure yourcomputer is PCMCIA supported. If you

- -169. The rest of the installation should proceed automatically. At last, theon-screen instruction will prompt your to restart your computer to

- -17MANUAL INSTALLATIONYou may also manually install the CD-421 OS/2 device driver if thedefault setting conflicts with your system. Perform the

- -18ADDING PCMCIA SUPPORTPCMCIA Support can be automatically installed during OS/2 installationor it can be installed through Selective Install

- -196. Select the appropriate system (this should either be a direct matchwith your target install system or a known compatible system).Figure 1

- -20USE CD-421 TO INSTALL OS/2 WARPBefore you begin, make a back up copy of the “Diskette for CD-ROM #1”of OS/2 Warp.1. Copy EXPCD2.FLT file fro

- -21TROUBLE SHOOTINGThis section explains the most common error messages thatDOS/Windows users may encounter.After rebooting your computer, the

- -22v v Error: Illegal I/O port!The above message means invalid I/O ports in the EXPCDI line ofCONFIG.SYS has been selected. The legal I/O port

- -23 BASIC OPERATING PROCEDURESThe CD-421 is designed for both multimedia applications and forentertainment purposes. It can be used with your

- -24PCMCIA(PC CARD) SOFTWARE INFORMATIONIf you have installed the PCMCIA software, such as SystemSoft’sCardSoft or Databook’s Cardtalk, then EXP

FCC COMPLIANCE STATEMENTSThis equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FC

- -25The device driver names of the major PCMCIA software are listedbelow:Software/DeviceDriverSystemSoftCardSoftPhoenix AwardCardwareIBMThinkPad

- -26STACKS=9,256DEVICEHIGH=C:\CARSOFT\SS36SSL.EXEDEVICEHIGH=C:\CARDSOFT\CS.EXEDEVICEHIGH=C:\CARDSOFT\CSALLOC.EXEREM** The REM’s should be remove

- -27DEVICEHIGH=C:THINKPAD\DICRMU02.SYS /MA=D000-DFFFDEVICEHIGH=C:\THINKPAD\$ICPMDOS.SYSDEVICE=C:\THINKPAD\AUTODRV.SYS C:\THINKPAD\AUTODRV.INIDEV

- -28POWER SAVINGThe CD-421 may operate with an AC adapter or batteries. Use of thesupplied AC Adapter will provide the power for use as a porta

TRADEMARKSSystemSoft is a registered trademark of SystemSoft Corporation.CardSoft is a trademark of SystemSoft Corporation.Phoenix is a registered tra

CONTENTSINTRODUCTION... 1SYSTEM REQUIREMENTS...

- -1INTRODUCTIONThe CD-421 brings the latest in mobile computing technology tonotebook computer users with portability and convenience. The CD-421

- -2PART NAMES AND FUNCTIONSFRONT PANEL OF THE CD-ROM DRIVE•• Disc Tray:This disc tray is used to insert the compact disc.‚‚ Load/Stop button:• P

- -3 REAR PANEL OF THE CD-ROM DRIVE•• Interface Connector:This interface connector connects to the PCMCIA interface card.‚‚ DC in Jack:This jack

- -4POWER SOURCEThe CD-421 can be either powered by the AC adapter or by the batteriesas a flexible option. However, the AC adapter has a priori